MODERN MASTERS® ShimmerStone™ is a tintable, water base architectural coating that produces beautiful, shimmering effects with luminous undertones. This versatile product can be used to create a wide variety of decorative finishes that do not require burnishing or sanding, such as: layered stone, dimensional lace, linen, raw silk, and raised ornament. It is durable—yet easy to repair, water resistant, mold and mildew resistant, and will adhere to any primed surface.

Modern Masters ShimmerStone single Tintable Base can be used on its own or colored using the ShimmerStone unique Color Concentrates. The 15 designer colors are available in 2 oz. tubes and will create hundreds of hues ranging from ultra-deep to pastel-light. Choose the desired colors from either the ShimmerStone Color Deck or brochure. Each represented color will show the color name and the amount of Color Concentrate to add per gallon. All of the hues have been created using ordinary kitchen measuring spoons.

SURFACE PREPARATION:
Follow standard practices and procedures for properly preparing surfaces for the application of traditional water-based latex paint. The surface should be free of imperfections, sealed with a primer-sealer, and have a low sheen. If it is not, fill cracks and nail holes (ShimmerStone will also work well as a filler.) All surfaces to be painted must be entirely free of dust, dirt, oil, grease, and other contaminants. Completely remove all loose, flaking, or chalking paint from the surfaces. Use a NIOSH approved respirator when sanding and when working with old, loose paint particles. Provide adequate ventilation. Properly prime the clean, dry surface with either Zinsser Bulls Eye Water Base or Zinsser Bulls Eye 1-2-3® Deep Tint primer-sealer, following the label directions. TIP: Tint the primer-sealer to a similar hue as the ShimmerStone™ base color using the ShimmerStone™ Color Concentrates.

Tinting ShimmerStone:
Modern Masters ShimmerStone™ single Tintable Base can be colored using a ShimmerStone unique Color Concentrates, Modern Masters Metallic Paint Collection™ metallic paints, or Universal Tint Colorants. The 15 ShimmerStone™ Color Concentrate designer colors are available in 2 oz tubes and will create hundreds of hues ranging from ultra-deep to pastel-light. Choose the desired colors from either the ShimmerStone™ Color Deck or brochure. Each represented color will show the color name and the amount of Color Concentrate to add per gallon. All the hues have been created using ordinary kitchen measuring spoons. If yet deeper colors are desired, simply add one or more full tubes of color per gallon. STIR well using a stir stick or a hand drill with detachable mixing device. DO NOT SHAKE.
(TINTING NOTES: Metallic Paint Collection™ metallic paints vary in color strength and intensity always test before mixing large quantities, do not exceed 12 oz of paint per gallon, and do not store ShimmerStone and Metallic Paint Collection mixtures; do not exceed 8 oz of Universal Tint Colorants per gallon).

Applying ShimmerStone:
ShimmerStone™ can be applied with a wide variety of tools, creating numerous beautiful finishes. To achieve a layered stone look, use the following 3-step application method. The base coat of ShimmerStone™ should be the deepest hue, and then one or more lighter hues are applied over the base coat.
Step 1–Base Coat
With a stainless steel trowel apply a thin, uniform coat of ShimmerStone™ base color to entire surface using broad sweeping strokes and firm pressure. Allow product to completely dry, approximately 1 hour.
Step 2 –Texture Coat
Transfer some of the base color to a paint roller tray. Dampen the ShimmerStone™ Natural Sea Sponge Mini Roller and squeeze out excess water. Work in sections. Using the roller, lightly load it with the base color and randomly roll product over the surface in all directions, covering approximately 75% of the section’s surface. While product is still wet, use the trowel to “knock-down” peaks, by gently pulling across the surface, holding the trowel at a very low angle (25-30 degrees). The surface will now have some texture, consisting of raised and recessed areas. Allow product to completely dry, approximately 2-3 hours.
Step 3 –Skim Coat
Apply a skim coat of ShimmerStone™ in a different color or a lighter hue. The more contrast in color or hue, the more dramatic the effect. Work in sections. Load the trowel with product and using firm pressure, skim over the texture coat, pulling the trowel tight and towards you in an arc, approximately 8” in length. “Feather out” the edge of the section by rolling the Natural Sea Sponge Mini Roller, loaded with ShimmerStone™, into the edge, so that no hard lines are visible. This technique will help avoid lap marks, hard edges or build-up due to double application of product. Continue process until entire surface is coated. Around doorframes and in tight areas, use a small putty knife to pull and smooth out excess ShimmerStone™. Allow product to completely dry, approximately 1-2 hours.

Cleaning ShimmerStone™ Surfaces:
ShimmerStone cures to a durable, water-resistant coating; a clear top-coat is not needed. It can be cleaned with soap and water or a mild household cleaner using light scrubbing. However, harsh or abrasive cleansers, including the ‘soft scrub’ abrasive cleansers, should not be used, as they are likely to polish or change the appearance of the surface.

Film Properties (Drying times at 70°F and 50%RH):
Dry Times: Dry-to-touch time is approximately 1 to 2 hours. Full cure is in
approximately 2 to 3 days.Note: Lower temperature and/or higher humidity and a higher applied film thickness will lengthen the dry and cure times.

Coverage: One gallon will cover approximately 90 to 140 square feet.

Clean Up: Clean brushes, rollers, tools, and equipment with soap and warm water immediately after use. Do not reuse containers and properly dispose of empty containers.